How to Run Cable from Basement to Second Floor – Step by Step Guide
Cables must be connected from one place to the next for various reasons. Perhaps you’re installing a second TV. Maybe you’ve relocated your office to a new location, and you need to set up printers as well as Internet cables. When it is necessary to run a cable from the basement to the second floor, you’ll likely want the final result to be completely invisible no matter what the case. That means instead of going through the wall, you’ll pass through the wall. Electricians have made this design for a long time, employing fish tape, a long strip of steel with a hook on its end.
Thanks to the advancement in wireless technologies, computers can set up tables throughout the building. But sometimes require cables. It is possible to hire a professional to connect the cable from room space; however, this can be costly. This article will cover some of the strategies and tools needed to gain a broad understanding of how to run a cable from the basement to the second floor.
How to run a cable from the basement to the second floor
After you have checked the building codes and determined the building code, design the cable route. Switch off the power, and then drill holes in the ceilings of the first and second floors. Use fish tapes and mounts to secure your cable onto the walls. Connect the cable to the wall plate, then connect it to the appliance. Be ready because we will share the steps to run a cable from the basement to the second floor.
Don’t miss this guide. Read to learn how deep can you dig a basement.
Step-1
Following the safety standards in areas certain regions, any cable could be hazardous. Even though it permits you to use low-voltage cables, phone lines, speaker cables, and network cables, make sure you check the building code for specific cables.
Step-2
To connect an extension cable that runs from basement level to second, you’ll need two tools. These include a 3/4 inch cable mount, drill bit cables measuring tape, a cordless drill, hammer, and so on. Pick the appropriate cables with a more excellent quality fire-retardant rating suitable for your walls. Find out the distance between the appliances that make their use of cables. The cable must be able to run between floors and through walls and baseboards. This means that you have to be aware of these calculations also. The best way to do this is to always run a longer cable length than you need. This gives you more room to make adjustments later on.
Step-3
Locate the access point located in the mid-level of the second floor. The cable will run through the second floor and into the basement. It is recommended to pick an area close to the basement wall. Wires should not be buried in avoidable places. Make sure to disconnect the power supply to avoid damage to living wires.
Step-4
Get a drill that is cordless since your home isn’t powered. Put a 3/4 inch bit in training and begin drilling. Keep the machine at a 90-degree angle with the floor. After hitting the floorboard and floorboards, take out the drill. Replace the drill bit with a 12–16-inch extension. Then, insert the drill bit of 3/4-inch into it. Continue drilling in the exact location and at the same angle. Stop drilling once the drill reaches the ceiling of the lower area.
Step-5
Now the step is to connect the cables. Start at the upper levels, and then use mounting cables. After that, you can run the wires through the baseboards. A cable mount can hold the cable securely using its clip. In addition, its built-in nail will secure the mount to the baseboard’s surface. Set the mountains at each of the four feet. Then, place the cables in the horses and set them in the wall. Continue to do the procedure until you’ve reached the floor’s opening. The floors.
Step-6
Then, you’ll need to pass an extension cable through the holes. Straighten the hanger, and secure the cable to its length. The next step is to move the hanger and cable through the opening constructed in the first and second-floor ceilings. Keep pulling the cable away from the hole, moving it down to the lower levels. You’ll have to deal with no problem with tangling as you run cables across the walls.
Connect cables to those walls in the basement. Similar to the previous step, you can use mounts to connect them to walls and all the way onto the floorboards. Make sure that you place the mounts four feet from each other. Then connect your cable to the previously determined devices and turn the switch on the power source.
How to run a cable from the basement to the first floor
Step-1
Check the wall on which you’re planning to put the cable. Look for outlets. Mark the area on the wall where you’ll be drilling into the basement wall. This is far from outlets or other wires running through the walls. The holes should be low to the ground to be less noticeable. Take a measurement of the distance to the wall’s edge.
Step-2
Take a trip upstairs and mark an area just above the basement area. It doesn’t have to be directly above the site, so you can put the spot in a quiet location. Keep in mind that the more direct you travel, the easier it is to search for cable.
Step-3
The batter light should be turned on and shut off all power for the home. Your mark is likely to be located in a location without wires, but there was a chance there was a problem. You do not intend to drill through an active wire.
Step-4
Create a rectangular cutout into the wall in the two rooms where you have marked the spots for cable. Although you don’t require an enormous hole in the wall in your basement, you’ll need a hole big enough to allow the drill inside the base of the 2-by-4 of the upper room.
Step-5
Make a hole in the 2-by-4 at the base of the wall upstairs to make a passageway to allow the cable. This hole should be wide enough to let the line go through.
Step-6
The outer edge of the cable and tie it onto the eye hook at the bottom of the fishing tape.
Step-7
Install the wire into the basement opening that you just sawed. The wire should be fed through the wall. Then, let someone else upstairs pull it through the hole. A coat hanger could help to catch the eye on the fishing tape when it passes through the hole inside the 2-by-4. Continue feeding this fish line until someone upstairs has taken the cable all the up to the point where it will end.
Step-8
Take the cable out of the fish wire. Pull the wire down the basement, then away from the wall. Connect the cable to an adapter. Create an opening in the drywall piece removed from the wall on your upper floor. The splitter is screwed into the drywall, So make sure that the cutout on the wall piece isn’t in conflict with the screws.
Step-9
The walls can be patched with a repair kit for drywall. Attach a tiny bit of dowel on the side of the hole in the wall with cement adhesive. Give it time to dry. Apply the masonry cement to the brace, then place the cutout of the wall that is dry in place back in the wall. Then, cover the joint compound using a trowel to create a smooth surface. Let it dry, then sand the area.
How to drill hole from basement ceiling to floor above
To make a hole in your basement’s ceiling up to the flooring above, you’ll require a cordless drill with a 3/4″ drill bit as well as an extension. Since power is cut and the drill will be cordless, a drill bit is what you’ll use. Install the 3/4-inch drill bit in the drill machine and position it to parallel the surface of drilling. Then, drill into the flooring and subfloor. Stop the drill machine and remove the bit. Attach the extension and place it back in the machine. Then, you can drill again precisely the same way until you’ve reached the ceiling.
Conclusion
The transmission cable from the basement to floors above calls for a system of steps. These procedures can be hazardous and require the assistance of a skilled electrician or someone with some basic understanding of them. That means that homeowners who aren’t experienced shouldn’t make decisions independently. Make sure you’ve learned how to run cables from the basement to the second floor.
