How to Resurface a Bowling Ball with A Spinner | DIY Hacks to Follow


Many people are often wondering how to resurface a bowling ball with a spinner? Pores characterize bowling balls that aid in it catching due to their friction in the lanes. Bowling balls put in bowling alleys these tiny pores are likely to accumulate dirt and oil as they age. The pores that are blocked no longer serve their function and, in addition, they negatively impact the bowling ball’s reaction. Resurfacing the surface of the ball aids in bringing life back to bowling balls.

This is a process that helps in the removal of oil and dirt out of the pores thoroughly. When a bowling ball is resurfaced, it sands its pores and brings back the sharp edges. The sharp edges on the upper sides generate friction, which allows the ball to grasp the lane, thereby improving the chances of hooking. It is crucial to know how to resurface a bowling ball with a spinner or without a spinner. The coating can also aid with making your ball travel across the rails much more quickly than it did before. To resurface bowling ball, please follow our directions. Here we will try to teach you both methods. Read on!

What is the reason to resurface a bowling ball? 

Every ball is flush with pores. They enhance its hooking potential by generating more friction and an enhanced bowling ball action on the lanes. However, when bowling balls are continuously released into the bowling lanes, the tiny pores are prone to accumulating oils and dirt. As a result, the blocked pores cease to serve their function and adversely affect the ball’s speed and reaction. A bowling ball that is not responsive is often referred to as “dead ball.”

Resurface a bowling ball with a spinner make your bowling ball helps to bring new life to your game. This process assists in removing debris and oil off the ball. If you want to revise the surface of a bowling ball, you apply sanding techniques to remove lane oils and loose debris from their pores and make them sharp again. Sharp edges with an elevated angle can create friction that allows the ball to hold the lane more tightly and increases the hooking potential for the bowling ball. Resurfacing also makes your ball move through the lane faster than it was before, enhancing the performance of your ball and creating the illusion that you’re using a brand-new bowling ball.

How to Resurface a Bowling Ball with A Spinner

When resurfacing a bowling ball

The principle is that you should clean your bowling ball at least in each 60-minute game. Then, you can resurface your ball until you see the brand logo disappears. If you cannot notice the logo thanks to the frequent sanding, it’s time to buy a new bowling ball. Why would you want to buy a brand new ball, you may ask? Once a certain amount of time passes, the resurfacing process becomes an unfinished business. It does not help bring the ball back to its former glory.

How to resurface a bowling ball with a spinner

In most cases, the bowling ball will take several times until the developer’s name hide from your neighborhood. Therefore, if you attempt to revive a bowling ball inside your house for the first time, or you’ve already managed the development by resurfacing the bowling ball multiple times, the outcome is identical. The first step when upgrading the bowling ball’s surface is to decide what results in you would like to get from the upgrade process. The final goals will determine the type of grain you choose to use in the sanding process you’ll use.

The lower grain will assist your ball in driving more efficiently along the lines with oil and is appropriate for players with lots of ball agility associated with a small number of turns because they give your ball a larger area. The higher grades will leave less space on the ball and are ideal for players who want greater control since higher grain can increase the hook’s length when bowling spinner. Based on the sanding method that you employ, it is possible to create a pre or post hook.

Checkout: How to clean a bowling ball with rubbing alcohol

How to Resurface a Bowling Ball with A Spinner

Sanding bowling balls

The standard method for sanding a bowling ball is to cut the sand in 90-degree angles of the ball’s initial sanding agent. If instead, you use the track from the beginning, it will give you an extended length of attached with a higher rake at the side of your track. For a smoother roll with a more friendly backend, you’ll need to sand your way across the initial traces of the ball. However, suppose you’re not seeking to achieve an objective with an exact sanding method. In that case, It is generally appropriate to put the bowling ball on the roulette wheel, with the middle of your hand at the top after completing the sanding process.

After you have finished the sanding process, you’ll rotate your ball 180 degrees as you work on the area turning the ball in 90-degree angles. After that, you’ll turn the ball 180 degrees and continue to sand to ensure you’ve removed all the material on the ball. Additionally, it’s ideal to continue in the following order: label, opposite label, the top and bottom of the label’s side, and the left and right labels’ sides.

Step 1

The bowling ball must place upon the spinning. Make sure that the gripping finger holes are on top. Set the spinner’s speed to the lowest setting. If you are sanding in a high-speed environment, it increases the chance of making mistakes.

Step 2

Before you apply a sanding agent for the bowling ball, you need to know the grit content on the pad. The majority of sanding pads start at 180 grit and can increase to 4000! Experts say that the higher the grit and the smoother the final result you can anticipate. If you are employing sanding pads that have lower grit, use more pressure for a shorter time. Use less pressure when using a high-grit pad. The higher grit pads need to use for more periods in comparison to the fewer grit pads.

Using a pad with a lower grit will allow your ball to perform better on the heavily oiled lane. It also provides the ball with more surface too. Bowlers using high grit pads are likely to want more control over their ball. The higher grit pads also allow for longer hook times for your bowling ball. Select a grit pad you prefer and then utilize the same place across the entire ball to ensure an even grit.

Step 3

Then, you can begin working on the area of your bowling balls. Pay attention to the ball’s initial pattern of sanding to ensure an even surface on your ball. Cover the exposed areas of the ball thoroughly. After you’ve completed the first part of the ball, move it back to the center. It by putting the finger holes on the bottom and repeating the sanding process in the opposite direction. After that, you can reposition the ball once more by making finger holes on the sides. Continue until you’re done with sanding all the surfaces.

Step 4

When you’ve finished sanding your ball, spray water to wash away the dust and then wipe it clean. Apply polishing agent. Make sure that the spinning ball is set to the maximum speed setting. Utilizing a towel, evenly apply the polishing agent to all balls, ensuring that it sparkles.

How to resurface a bowling ball at home

There are two methods to resurface bowling balls. You can go to your local pro shop, or you can resurface at your home. Resurfacing by a professional bowling ball is the most beneficial option as he is likely to have access to the most modern equipment and tools, which will allow him to do the job faster and will likely create more uniform ball surfaces. In addition, the risk involved is less than attempting to resurface yourself.

Sanding agent

There’s a wide selection of sanding agents for the sale. There are various options, including Sandpaper discs for sanding discs and abrasion pads, air sanding pads, and much more. Pick a sanding machine that you’re comfortable with. You might be able to locate a kit that includes both an abalone pad and a cleaning agent.


There will be lots of dust generated during the sanding procedure, and you’ll need to continue spritzing water to remove dust from the sanding pad to ensure an even surface. Think about purchasing spray bottles to help make the water spraying process effortless and hassle-free. Sanding can produce heat due to friction. The water can also help keep the ball cool.

Polishers, towels, cleaners

For the final step of this resurfacing procedure, you can polish the ball using a new towel. You can also think about using several polishing pads to improve the sparkle of the ball. Polishing pads are available from many online stores or local professional shops.


Resurfacing a bowling ball is a DIY project that can be accomplished at home, provided you have the proper tools. Also, it is essential to make the best usage of the ball’s spinner DIY. Bowling ball sanding is complex if you aren’t sure how to accomplish it. Resurfacing the ball isn’t to all people’s tastes. If you’re not confident about tackling it yourself, don’t hesitate to go to one of the local specialist stores.

Leave a Reply

Your email address will not be published. Required fields are marked *

twelve − 6 =