How to Remove Oil from Bowling Ball – Genius Cleaning Hacks for Novice


Your bowling ball will begin to absorb oil and dirt over time. Initially, the oil ring will appear around the ball’s surface. You have to remove oil from the bowling ball. Otherwise, the ball will ruin. It will absorb resin from the cover stock if it isn’t cleaned up as soon as possible. You can make the ball react differently to the lane, and it will not respond the same way as before. You’ll find it more difficult to throw the ball, and your grip will become less secure. Your bowling ball’s life expectancy will be extended if you take good care of it.

There are many effective ways to remove oil from a bowling ball. This will allow it to perform at its best for an as long time as possible. The easiest and most efficient way to do it is with a bowling ball rejuvenator to remove oil from your bowling ball. You need to be aware of when the ball will clean. This will ensure that the ball stays in good condition. You have options: you can clean it at home; you could also take it to a Pro shop or get your oil extraction machine.

What causes the bowling ball to turn to oil? 

A ball can become oily for many reasons. Your ball get oily because it is roll in the lanes. This dust causes the ball to oil. It also matters what kind of materials the ball made of. A ball made from plastic will emit less oil than a resin ball. To prevent them from becoming wood-dead, oil should be used to cover the lanes. Oily lanes can make the ball oily from its rolling.

how to remove oil from bowling ball

How to remove oil from a bowling ball? 

When your bowling ball doesn’t roll smoothly on the lanes, you will know it is oily. If you play regularly on oily streets, you must clean the ball every 30-40 games. If you remove oil from the bowling ball, clean and dry it, it may be possible to clean it every 70-100 games.

Learn more: How to clean a bowling ball with rubbing alcohol

Cleaning with rubbing alcohol 

Using rubbing alcohol for cleaning is also a quick way to remove the oil from the ball. Use a bucket of water to mix rubbing alcohol with. You should ensure that the water to rubbing alcohol ratio is at least 4:2. Put the towel in the bucket. Now squeeze the towel to remove any excess water. Use this towel to wipe down the ball. You will have an oil-free ball.

Bowling ball cleaner spray 

This is the quick way to clean your ball. Use equal amounts of bowl cleaner spray with water to spray the ball. Use a towel to wipe off the solution. Be sure to remove any oil. You can buy the ball cleaner spray from online or at any supermarket.

Heater method 

This is very similar to the hairdryer and oven methods. Place the ball on a towel and place it in front of a heater. You can then heat the ball so that it releases oil. If the oil isn’t removing anymore, you can stop heating it.

Using hair dryer 

Although this method is risky at times, it can still work if you take care. A hairdryer heats the ball’s shell. Oil is released when the ball’s surface is heated. Place the ball on a towel. Blot the dryer so that the ball rotates constantly. Gradually, the oil will start to seep into the ball, and it will become shiny. You can now wipe the oil off the ball and keep going until the oil stops releasing.

Baking the bowling ball 

The baking ball is a heat-based method that removes oil from the ball. When the ball is heated, its pores open, allowing oil to be released. The ball should be hit at a temperature of 140 degrees F.

Clean from pro-shop 

It can be challenging to clean oil off a ball. You can hire a professional to clean your wall if you don’t have the time. These shops can use equipment to remove oil. These shops use machines that spin the ball at high speeds to release oil and clean the bowling ball. Oil-removing spray is also available at some shops. This treatment can be costly overall. We hope you find one of the following methods helpful in removing oil from your bowling ball. Each individual can choose the oil-removal method that they prefer. You can try another way, but none of them will work.

How to remove oil from a bowling ball by Immersion Method

How to bleed a Bowling Ball

Fill a bucket with hot water

Find a bucket and fill it up with water. The water should not boil, but it should still be warm. A sink or any other large vessel that can hold a bowling ball and enough water to submerge the ball in it is also possible. You will soon have a lot of oil in whatever you choose, so be aware. Fill the bucket only halfway. Fill the four-quart bucket as shown in the picture. It would help if you still filled the pail to about half full. This will prevent water from escaping and cause flooding.

Tape over the holes 

Before putting the ball in the water, cover the holes with duct tape or water-resistant taping. Although some people don’t think this is necessary, it could lead to your ball getting waterlogged if the holes are left exposed. This is why this method isn’t the best one for cleaning your equipment. You can either loosen the glue from your grips or soak the ball in water if you don’t tape the holes properly.

Immerse the bowling ball

Place the ball in the bucket. The oil will start to seep out of the ball, and then it will begin to bubble up on the surface of the water. Add more water if the waterline is not covering the entire ball. You’re fine if the water gets everywhere when you put it in, except for the mess you have to clean up. The ball should remain in the water for between 20 and 30 minutes before being removed.

Clean the bowling ball 

The oil in the bucket will make the ball very slippery. Wipe the ball with a microfiber towel to get rid of any oil.

Let the bowling ball rest 

Please take off the tape and place the ball in a dry area with holes in it. This is particularly important if the holes are not cover. If you didn’t cover the holes, the ball could likely be used immediately. However, it won’t hurt to let the ball rest. The ball should grip the lane better next time you use it. If it isn’t, the ball may be at the end of its life.

How to soak a bowling ball in hot water 

Manufacturers have mixed reactions to this issue. It would help to verify with the manufacturer whether your items are safe to soak in hot water. The procedure I used was quite simple. Before you wash, first lower the surface to 360 grit or 500 grit. This will allow the oil to escape from hot and soapy water. Once the surface grit remove, you can seal the bucket using hot tap water. To make a frothy mixture, add some Dawn soap. Be sure to remove any tape from the thumb hole and any other hole before you soak.

If the tape is left in the hole, it will likely melt and leave a sticky residue that is difficult to remove. Place the ball in a bucket and soaked in hot soapy water for 20 minutes. It would help if you submerged the ball in soapy water. After the soak, rinse the bowling ball to remove any soap residues. However, you can scrub the surface with a rag before you throw away the soapy water. To finish drying the ball completely, use a dry cloth to remove any water traces. Next, spin the ball around on a ball spinner until the ball is in the desired position.

Find more: How to resurface bowling ball with a spinner


There are lots of ways to remove oil from a bowling ball. There are two options: professional or DIY. You can choose which method you prefer. Hot water is the easiest of all the ways. Before using any of these methods, it is best to allow the ball to dry completely. If you compare the cost of professional cleaning, do-it-yourself is more affordable than professional. We tried our best to provide information on how to remove oil from a bowling ball. It would help if you cleaned your bowling ball regularly to keep it in good condition. When your ball rolls smoothly on the lanes, and you are in the first place, nobody can stop you! Enjoy bowling!

Leave a Reply

Your email address will not be published. Required fields are marked *

thirteen − 9 =