How to Lay Vinyl Tiles In A Bathroom Wall | Expert’s 8 Simple Steps


In contrast to other flooring materials, vinyl flooring only uses a flat subfloor. Make sure you work on a level, flat surface to avoid “slippage” or one piece being over the other. Vinyl tiles can generally be placed directly on ceramic tiles, provided that specific guidelines are adhered to. Learn how to lay vinyl tiles in a bathroom wall. Remodeling your bathroom or shower is among the most expensive and longest-running home improvement projects you’ll take on. Because of the selection of materials available in the market, there is plenty of room for exploration. Since luxury vinyl planks look attractive and long-lasting, you might think about whether they could be used on your bathroom or shower walls. It is possible to install a water-proof, scratch-resistant, and durable vinyl plank on bathroom or shower walls. Cork underlayment shields against mildew, water, and mold damage on WPC or SPC Vinyl planks. Therefore, they are ideal for bathrooms. Therefore, let’s look at what you can do:

How to lay vinyl tiles in a bathroom wall

Determine the fair amount as yards sq. Before you calculate square yards, estimate square feet. Then, measure precisely bathroom dimensions. For instance, multiply the length by the width to determine the space. Per square foot, a yard contains 9 square feet (9 square yards). A room measuring twelve feet by eight feet has a space of 96 square inches. This is 10.67 sq yards.

Step 1

With graph paper, sketch the floor plan in scale. Be sure to measure under appliances that move and within closets. If you plan to cut and then fit, add 3 inches around the perimeter instead of using templates.

Step 2

Before you lay your vinyl down, finish a few primary tasks within the room. First, remove all appliances, furniture, and appliances in addition to the toilet. Get rid of the doors and hinges from the frame of the door. Clean up using gloves if you’re wearing them. If you combine an edged trowel with a straight edge, the embosser produces smooth surfaces to aid in installing the new flooring. Make sure you remove damaged or damaged vinyl flooring before you can install it. The floor made from wood or with an embossed or cushioned surface must have an underlayment. The new base will expose any flaws in the flooring.

Step 3

The only requirement to install sheet vinyl is smooth and clean with a dry surface. Then, fill any fissures or gaps that might have formed. Make use of a grinder to lower your height at high points. Make use of a masonry chisel and smaller sledgehammers to eliminate flaws. Glasses for protection against eye injuries can help. Sheet vinyl can be installed over linoleum flooring or floors in good shape. Use an embossing leveler if the floor is old and has a rough surface or indentation.

Step 4

In the end, the new wall or floor will be able to replicate the features of the floor underneath it. Choose plywood underlayment if the area you cannot eliminate is the old one because it is too rough to be used as an embossing leveler. Unless the local building code stipulates otherwise, using 1/8-inch BC plywood is a good underlayment. Make use of plywood graded for underlayment when you are planning to make use of it. This can raise the floor. Cutting the bottoms of the door frames and re-installing the thresholds are required to allow for the new height.

Step 5

The installation of the underlayment is now feasible. The new underlayment can slide underneath the door molding by cutting through the molding’s bottom edges. In addition, it is possible to determine the proper distance between tiles using the help of an underlayment.

Step 6

Ring-shank nails are a great way to fix floorboards that are sagging or old. Fill in any holes or cracks in the floor caused by the pins you put in. It is recommended to leave a tiny space between the plywood panel seams to permit expansion. Maintain an inch between the wall and ceiling as a general rule. Use the screws and pattern suggested by vinyl flooring manufacturers and the plywood. Utilize a floor leveler or a cement mixture (patching) to cover the gaps between the underlayment panels. When dry, you can sand the floor to an even surface. Clean the flooring thoroughly. There should not be any dust, lint, or wax on the floor. Make use of adhesive products.

Step 7

Vinyl flooring comes in sizes of 6-foot and 12-foot, which allows easy installation within smaller spaces like hallways, bathrooms, and kitchens. Before cutting, you should enable the flooring to adjust to the area by allowing it to sit for a minimum of 24 hours. There are two methods to measure and place vinyl. First, you can take measurements of the entire floor, then make the cut 3 inches wider on every side over the flooring. Afterward, you can place it in the desired position and cut off all excess fabric. This method works well in smaller spaces with a limited number of edges or obstacles. Another option is to make a floor plan template. Before applying, transfer the design to the fabric and trim it to size. Use this method with thick vinyl or in rooms with difficult angles or corners.

Step 8

There is a way to reconnect baseboards and shoe moldings similarly. Lift them above the ground to allow the molding to expand. If you are not planning to install flooring, it is recommended to place the molding. The changes in humidity can cause the flooring to stick to the tight molding. If you are replacing an old floor, make sure you have a seam that is 6 inches away from the seam that was previously used.

The vinyl can be covered on any flat surface, which includes wood, concrete, or even another layer of vinyl. The remaining tiles can be used. The edges of the vinyl tiles should be in line with each other. Be sure not to overlook a pattern that repeats in the tiles. Be sure to keep your bathroom walls clean of dust. Create a cardboard model of the area, trace it on the tile, and cut it as required using a utility knife. Then, keep going as you would expect following the being missing. After completion, ensure your tiles have been set in the desired position. If you notice any troublesome areas, you can roll them using the help of a pin or tile roller.

How to lay vinyl tiles in a bathroom wall: Tips

  • Then, draw your floor plan using a washable marker on the vinyl sheet.
  • Before cutting vinyl, make sure you protect the floor. What do you do? You can place a piece of plywood (scrap) beneath it.
  • Let the edges of the vinyl curve against the wall when you position it on the wall. Set aside 3 inches for trimming on both sides.
  • After cutting a vertical line across the sheet and cutting it to the floor’s floors.
  • Utilize a knife for the utility to cut V-shaped lines in the vinyl when it is overlapping. When you’ve reached the end of the vinyl, make a few V-shaped cuts as you go.
  • When the wall is at the point of the floor, you can create it by pressing the 2-by-4 over it. After forming the crease and cutting the flooring, you can cut it with a straight edge. Because expanding the flooring leave a gap of 1/8-inch between the floor and wall.


The vinyl plank floor is trendy due to its flexibility and resiliency. It’s comfortable on your feet and gives your room an elegant and refined look. In addition, vinyl flooring can be a smart option for families with kids and pets because of its noise and stain-resistant characteristics. Flooring made of vinyl planks is widely used in basements and bathrooms for the same reason. But the contrary, you can put Vinyl plank flooring inside your bathroom or kitchen.

Leave a Reply

Your email address will not be published. Required fields are marked *

one × 3 =