How to Install a Utility Sink in The Garage | DIY Simple & Easy Steps
The process of preparing yourself for plumbing and installing the plumbing utility is an easy task. No matter if you’ve already installed one before, it is possible to complete the job quickly and without the hassle, and you don’t require the help of a plumber. In this tutorial, I’ll tell you how to install a utility sink in the garage. Many people consider this idea due to the benefits of this kind of sink. However, installing it in garages is the dream of intelligent and practical people as it is the ideal place to put it.
Installing a sink of this kind in your garage can allow you to create an area exclusive to dirty clothes, which keeps you away from other areas of your house. However, the sink for a utility is typically strong and can hold a lot of water. They are mainly used to soak and wash clothes. They can also use for cleaning different types of appliances, including appliances and kitchen utensils. Because of this, intelligent people like you are thinking of installing their utility sink yourself. The process of installing utility sinks is easy that they usually require about 30 minutes or less.
To do this, you’ll utilize specific and straightforward tools. Through this post, you’ll gain the knowledge you need to understand how to install a utility sink in the garage without any hassle.
How to install a utility sink in the garage
When working in garages, you usually require a water source for transport. However, things will get complicated in the absence of a suitable medium. You can, however, use the utility sink. So, why bother about this when you have it back! The first step is to install a utility sink in the garage is to close the water valve. Next, you need to determine the distance between the waterline and fix the coupling. Next, locate the drain connector, and connect the P-trap. Then, construct the countertop. Then, you can finish the installation. You’re in the right location to reach the component you’ve been searching for! However, don’t give up as the primary part is still waiting for you!
Step 1
The first step is to must shut off the main shut-off water valve. Be sure to turn the handle with a firm grip. Otherwise, you may need to replace it due to the unnecessary cost to the valve. Make sure to check the faucet you use to determine leaks. Switch off the tap, which supplies water to the home and other faucets. Let the faucet go by switching on the cold and hot water supply. Remove the faucet currently in use from an old sink for utility. Take an older P-Trap off the tap. Take the sink off the floor.
Step 2
You must now determine the distance between warm and cold lines. Also, make a note of the space you’d like to set up your sink. You can cut two pieces of copper tubing in the length you want. You should allow for more inches than you require. Any extra tubing can remove at a later date. Even though copper is vital, make sure to keep the distance to less than 10 feet. You’d like your water to flow freely in the pipes that connect to the sink. Make sure that the sink is closer to the lines. In the event of a leak, there will be more leaks. Problems may occur shortly.
Step 3
The wall is where you consider the hot and cold pipes of water that are visible. Attach a compression coupling at the pipe’s end using your wrench. Make sure that the collar is secure and does not break. Be aware that you can use a variety of lines to accomplish this. Get your copper tubing that is soft now. Connect one end of the pipe with the coupling. Continue with the second pipe the same way. Connect the line to the coupler using a compression fitting. With your crescent wrench, make sure you tighten the pieces. One tube can hold hot water while the other has cold water. Note which one is which. Ensure that you can correctly connect them when installing your plumbing and sink later. You could make use of the magic marker or even an e-label to mark the location of your sink.
Step 4
Find that vent pipe for the drain connector today. It’s usually located close to the floor and is further down the wall. Install plumber’s glue to the threads of this pipe thoroughly. Connect the Y fitting’s end using a screw. The other part of the “y” section points down. Once the putty is dry, it should seal watertight. Attach the drain assembly’s flange section to the top of the Y pipe. The filter is part of this.
Specific drain assemblies are part of the purchase of faucets. They are available separately too. You might decide to add garbage disposal. If that is the case, it is possible to purchase an extender flange to bridge the gap. If you do not put in the drain connector correctly, there may be centipedes inside the drains.
Step 5
Install the P-trap to the opposite part of the Y. PVC pipe utilize to create the P-trap. It blocks air or gas from getting into your drain and creates smells. Apply the plumber’s putty on the threads to create a secure seal. Before connecting the Y part with the drainpipe used for the main drainage, ensure that it’s completely furnished. The Y component should be screwed in and secured with an adhesive for plumbers. Be sure to place the pipe on an angle that allows water to drain correctly. It is possible that water will not drain downwards when it is not level. Keep in mind one fact! You may not possess a p trap. It is possible to make use of an s-trap instead of the p-trap.
Step 6
The first step is to measure the sink. You can also utilize a template included with the majority of sinks. For reference, you can use these measurements. After that, the sizes, make a cut in the wood. Create the countertop using this piece of material for the foundation. It will support your sink and connect everything using nails made from wood. Make sure that the countertop is supported and consider the dimensions and weight of the sink. There’s a chance that you don’t require a full cabinet for the sink. It’s still necessary to have a solid foundation to help support your sink. Ensure your kitchen sink drains correctly, ensure the surfaces are perfectly level.
Step 7
Install the sink after the countertop is completed. Connect the water pipes to each faucet handle and set up faucet fixtures. Ensure that the faucet and the sprayer head are connected with suitable lines. It is possible to do this step even when the sprayer is located within the faucet’s spout. Get rid of all dried-out silicone and plumber’s putty, which has accumulated. You can now switch on the water source. Your sink is in good condition. Allow one second for water to flow. Make sure there are no leaks in the area behind the sink. Examine the faucet, drain connections, and the P-trap. Then you’re all set! These are the steps you must follow to install a utility sink in the garage.
Cost to install utility sink in the garage
On average, a sink installation for utility costs between $40 to $200. So, installing a sink worth $100 costs $200. Similar to the expense of having plumbing installed can vary between $50 and $100 and beyond. A plumber could charge as much as $200 to install a kitchen sink. These costs do not contain additional charges for other options. If no vent or drain pipes are operating, additional expenses would need to be made for their installation, just as when a plumber is responsible for the task.
In some instances, installations can cost 500-1000 depending on the features you decide to include. Prices for plumbers can differ because of whether or not an existing vent or utility sink must be installed. Before starting work, make sure you inquire about the bill as quickly as possible and then ask for a cost estimate.
Conclusion
Install a new sink can be a challenge, but it’s not complicated. You must be patient, and, of course, it is essential to utilize the right tools. It is easy to incorporate if you have the appropriate tools and procedures. If maintained properly, the sink will remain solid for years. After all, connections have been installed, you can check your entire tap. There could be several leaks or holes that need to be tightened up before turning off the water. Switched off. I hope you will better comprehend how to install a utility sink in the garage by studying this article.
